Ryan’s ‘23 A91MT Burnout - Slow Build

RyanA90 · Mar 12, 2023

Installed Torque Solutions Billet ride height sensor bracket since the oem plastic one snapped during the Dyno Runs. If you plan on strapping your car down on ANYTHING this is a must!

RyanA90 · Mar 13, 2023

Thanks to @NJA90 for the @Rexpeed @A90 Shop CF Bumper inserts +7 whp

NJA90 · Mar 13, 2023

Looooooks dopeeeeee

RyanA90 said:
Thanks to @NJA90 for the @Rexpeed @A90 Shop CF Bumper inserts +7 whp

RyanA90 · Mar 22, 2023

@A90 Shop CF Hood vents with mesh +2 whp +.3 wtq

RyanA90 · Mar 22, 2023

K-Brace finally shipped, enjoy the pic while we wait!

RyanA90 · Mar 25, 2023

I tried installing the K Brace this morning, I expected it to be direct bolt on since that's what it says on their website but its not. It didn't even come with instructions, the website it has some generic instructions. No pics or anything SMH!

I tried guessing the mounting points but I'll need a few things in order for it to bolt up and work.

Comes with bolts, mounts, and rivet nuts

Here's what the trunk looks like without the liner and panels

Looks like some sound deadening materials on both sides

This is where i'm assuming the rivet nut is used with the supplied mount, I'll need to buy a drill bit to make the hole large enough for the rivet nut to fit.

The supplied bolt does not fit here, seems too big in diameter. Doing my research its supposed to be M8-1.25, gotta go Home Depot and buy 2.

Other side

NitroYellowMKV · Mar 25, 2023

RyanA90 said:
I tried installing the K Brace this morning, I expected it to be direct bolt on since that's what it says on their website but its not. It didn't even come with instructions, the website it has some generic instructions. No pics or anything SMH!

I tried guessing the mounting points but I'll need a few things in order for it to bolt up and work.

Comes with bolts, mounts, and rivet nuts

Here's what the trunk looks like without the liner and panels

Looks like some sound deadening materials on both sides

This is where i'm assuming the rivet nut is used with the supplied mount, I'll need to buy a drill bit to make the hole large enough for the rivet nut to fit.

The supplied bolt does not fit here, seems too big in diameter. Doing my research its supposed to be M8-1.25, gotta go Home Depot and buy 2.

Other side

Keep me updated on this, if it’s not terrible while everything else is apart for the speaker mod I’ll do this

RyanA90 · Mar 25, 2023

Ok i was able to to get the needed parts to get it on but now there’s fitment issues, I’ll contact them Monday….

RyanA90 · Mar 25, 2023

Should I use washers?!

Rob901 · Mar 25, 2023

The holes look too off for washers, no?

RyanA90 · Mar 25, 2023

2 washers on each side on the top bolts did the trick!

RyanA90 · Mar 27, 2023

Here is the finished Product. Had to do some final measurements and cutting to properly fit the panels.

Fitment 8/10 - They gave the wrong bolts for the bottom brackets and I had to adjust the top part with washers on both sides.

Quality 9/10 - Solid piece with your color choice of powder coat.

Install took me about 3-4 hours. There are no instructions, pics, vids, etc.

No review until I take it to the canyons. But from spirited driving going on on-ramps/off ramps on the freeway it seems more planted like body roll is much less noticeable or even eliminated.

RyanA90 · Apr 2, 2023

Extreme Online wing (Artisan Spirits Rep)

<--Artisan Spirits rep vs TRD Rep-->

RyanA90 · Apr 3, 2023

Hi

s0_Salty- · Apr 6, 2023

RyanA90 said:
Went and did a few pulls at the Dyno today. No I never did bone stock runs SMH!

Fuel: 91
Intake: CTS w/ dinan inlet
DP: Kenji 200 Cell
Tune: Stock

400whp/410wtq

Nice you went to Ed for tuning!

Ryan’s ‘23 A91MT Burnout - Slow Build

RyanA90

Well-Known Member

RyanA90

Well-Known Member

NJA90

Well-Known Member

RyanA90

Well-Known Member

RyanA90

Well-Known Member

RyanA90

Well-Known Member

NitroYellowMKV

Well-Known Member

RyanA90

Well-Known Member

RyanA90

Well-Known Member

Rob901

Well-Known Member

RyanA90

Well-Known Member

RyanA90

Well-Known Member

RyanA90

Well-Known Member

RyanA90

Well-Known Member

s0_Salty-

Well-Known Member

Similar threads