Sponsored

Search results

  1. Bm3 rev2

    FWIW, the only adapter that’s never given me a single issue is the MHD Universal one. Manually set your IP to 192.168.4.2 (Lowest assignable IP, 4.1 is reserved for the configuration panel.) and your Subnet Mask to 255.255.255.0 and it’ll connect instantly every time without issue. This new...
  2. Bm3 rev2

    Make sure your device is not connected to WiFi/CarPlay/Bluetooth and hop into Settings/Ethernet and wait for the IP to populate. Once you see it populate, you’re good to go. If it doesn’t, disconnect the negative terminal on your battery for 5-10 minutes to reset the vehicle’s network.
  3. Bm3 rev2

    Today’s app update brought a firmware update that’s supposed to help with this. Haven’t tried it myself yet.
  4. DAW Ultraflow Gen 6769 Paired with what air intake?

    I didn’t say anything about dyno numbers. Also, get rid of that fucking attitude when someone asks a simple question.
  5. DAW Ultraflow Gen 6769 Paired with what air intake?

    What are your numbers looking like? I haven’t really seen anyone post 6769 numbers on kill.
  6. Help with spark plugs

    This.
  7. Help with spark plugs

    You don’t need it and you won’t make more power by using it. Stick with the stock 96206 plugs.
  8. Remnant Performance - Omega 65 Turbo solution for RHD cars

    I would definitely grab one from you if I ever pick up a Remnant turbo kit. I see in your description that 6 ports are at the buyer’s risk though so I’d wait until someone else confirms fitment.
  9. Remnant Performance - Omega 65 Turbo solution for RHD cars

    I don’t have an Omega 65 but nice work! This needs more exposure for sure. That stock bracket has always been an eyesore when I’ve seen it in photos and it looks like it was poorly made.
  10. 6mt MHD vs BM3 which is better in 2025

    In the “here and now”, MHD is the better buy because it has more advanced features actually available to the end-user. bm3 does have their CustomROM v2 and Rev2 board on the horizon but they are only available for the S58 currently and will likely remain that way until later this year. Also for...
  11. MST V2 with CTS or Paradigm Inlet?

    I’m honestly not sure. Maybe either my inlet or charge pipe was from a bad batch and dimensions were off a bit?
  12. MST V2 with CTS or Paradigm Inlet?

    That’s odd. I had the opposite experience. I had the CTS intake, inlet, and charge pipe when I was on a stock turbo and it rubbed the powdercoat away and ate into the aluminum.
  13. MST V2 with CTS or Paradigm Inlet?

    FWIW, don’t waste your money on the CTS one. It fits like shit and the breather bung will rub against your charge pipe if you have an aftermarket one (Even CTS).
  14. Replaced rear pads and sensor but not give the option to reset light

    Glad you got it sorted, but I’ve never encountered a scenario where what I just recommended did not work. Everyone who has ever came to me asking for help with this issue said it was resolved by following the steps that I just listed, in that exact order.
  15. The Secret: Loud Turbo Sounds on a B58!

    Skip the vendor tax and go straight to the source. @t51r_mods on Instagram is the guy who makes these for them.
  16. Replaced rear pads and sensor but not give the option to reset light

    The brake service function is extremely specific with the environment that it needs to be in to allow the reset. Put the car in diagnostic mode with the transmission in park, disable the parking brake, and then remove your foot from the brake pedal and it should allow you to reset.
  17. Sportscat DP Codes - Please Help!

    It wouldn’t be set unless you explicitly set it yourself. It’s in the flash options on the same screen as the big orange “Map Write” button right before you flash. Scroll through and look for “DP Configuration”.
  18. Sportscat DP Codes - Please Help!

    Did you switch the “DP Configuration” option in the flash settings to aftermarket? That’s what should disable the CELs. If you did and you’re still getting them, shoot MHD support an email.
  19. Installing pure turbo cannot get the turbo to sit in the bottom frame rail

    For future reference for anyone who struggles with this issue, if you look at OP’s photo that he added, right below the “shelf” that the turbo is supposed to slot into, you’ll see a small thin sheet metal bracket bolted to the side of the block that’s supposed to hold the turbo coolant line...





Top