Supra Floor Mats

[Axix23]

D

Hey, I haven't seen any supra branded mats, but you should look into getting these. I personally have them and got them in a few days ago. I replaced my weather Techs liners which are complete trash! I would never buy from that company again. Don't waste your money on them. They don't fit right and slide all over the place even hitting the gas pedal. I had Weather Techs for a year and have been trying to find a replacement until I bought these. Hope it helps.

https://www.ftspeed.com/part/l1ty25...-heavy-duty-all-weather-floor-mats-2020-supra

did you out the anchors in? If not, it will slide all over. Weather techs fit like factory.

Sponsored

 

[Jay2004]

D

did you out the anchors in? If not, it will slide all over. Weather techs fit like factory.

There are no anchor points in the driver side of the supra. Only velcro for the stock mats.

 

[Axix23]

Your supposed to install the anchors provide from your weather tech mats. That’s why your mats sliding all over lol

 

[Boomer64]

There are no anchor points in the driver side of the supra. Only velcro for the stock mats.

The factory velcro pads are actually attached to a hard plastic disc and removable by turning them (1/4 or 1/2 turn), and lifting out. Just align and insert the Weather Tech anchors in place of the factory velcro pad discs. There are no instructions enclosed with the mats for this. I was lucky to figure it out!

 

[Jay2004]

The factory velcro pads are actually attached to a hard plastic disc and removable by turning them (1/4 or 1/2 turn), and lifting out. Just align and insert the Weather Tech anchors in place of the factory velcro pad discs. There are no instructions enclosed with the mats for this. I was lucky to figure it out!

Thanks for the heads up. I didn't know that, but the mats I bought to replace the weather techs and better and I really like them a lot more.

 

[Axix23]

Thanks for the heads up. I didn't know that, but the mats I bought to replace the weather techs and better and I really like them a lot more.

I was trying to explain that to you. It’s hard n a forum. lol

 

[Jay2004]

I was trying to explain that to you. It’s hard n a forum. lol

It's no prob. Forums can be difficult.

 

[gtshnzr]

I think the Z4 mats will fit (shouldn’t they?) Part No. 51472461171 Going to order a set once the car gets here from NY and try them out at BMW dealership. If they fit, then have to figure out what to do with the Z4 logo

 

[2jzwho]

Just installed my garage alpha ones. They look amazing with the supra emblem in black chrome and the red borders.
I love them

 

[genoxy]

Got the weathertech liners today, the holes for the anchors don't line up which is disappointing. Could only anchor one side in so hopefully they don't move around too much... Anyone else have this problem or know of a solution? I though about punching another hole in the right location in the carpet...

 

[genoxy]

They look great way better than the weather tech ones. Is the 3d logo removable/not embossed into the mat? Was thinking of removing it completely or replacing it with a supra logo

Wish I'd seen this before ordering the weathertech ones... Do they fit with Velcro in original spots?

 

[Boomer64]

Got the weathertech liners today, the holes for the anchors don't line up which is disappointing. Could only anchor one side in so hopefully they don't move around too much... Anyone else have this problem or know of a solution? I though about punching another hole in the right location in the carpet...

Being an Australian spec model, you must have right hand drive. I bet the holes are oriented to be for a passenger side of the left hand drive model. Weathertech should have considered this for the RHD versions of the mat. I’d go after a refund or some kind of adjustment from them. A work around solution could be to use some heavy duty Velcro pads stuck to the back of the mats, to align with the factory velcro disk attached to the floor.

 

[genoxy]

Being an Australian spec model, you must have right hand drive. I bet the holes are oriented to be for a passenger side of the left hand drive model. Weathertech should have considered this for the RHD versions of the mat. I’d go after a refund or some kind of adjustment from them. A work around solution could be to use some heavy duty Velcro pads stuck to the back of the mats, to align with the factory velcro disk attached to the floor.

Yeah you're probably right... Ordered from FTSpeed in the US so return postage probably not worth it. Will try to find a work around for now, they don't fit perfectly either so might be slight variations with the LHD and RHD foot wells

 

[Jay2004]

Being an Australian spec model, you must have right hand drive. I bet the holes are oriented to be for a passenger side of the left hand drive model. Weathertech should have considered this for the RHD versions of the mat. I’d go after a refund or some kind of adjustment from them. A work around solution could be to use some heavy duty Velcro pads stuck to the back of the mats, to align with the factory velcro disk attached to the floor.

Velcro won't work, I tried it when I use to have the weather tech mats. The amount of pressure from your feet moving around won't keep it in place. I got rid of the techs and found a company that makes better mats the the techs for about a $100.

 

[gtshnzr]

I think the Z4 mats will fit (shouldn’t they?) Part No. 51472461171 Going to order a set once the car gets here from NY and try them out at BMW dealership. If they fit, then have to figure out what to do with the Z4 logo

Called the parts guy at the local BMW dealer. He has a pair of these Z4 mats in stock and sees no reason why they wouldn’t fit the Supra. More to come ...

Sponsored