What did you do to your Supra today?

[splv]

It came from the rear as he said.

TMI, my dude. You do you, but keep it clean.

 

[J29DB03]

It came from the rear as he said.

At first I thought the same thing but I think he meant the badge that replaced that one.

 

[EDUARDOP10]

It came from the rear as he said.

bruh.. i meant the one on the bumper not on the steering wheel lol.. i guess i should've clarified

 

[Danimal]

bruh.. i meant the one on the bumper not on the steering wheel lol.. i guess i should've clarified

No, you shouldn’t have needed to clarify…

 

[Danimal]

Ok, fine, to actually add to the thread:

This wasn’t all done today, but;

• EOS carbon skirts and spats - good customer service, mid/poor quality parts.
• xHP trans tune - amazing!
• Oil change
• Swapped back to summer wheels/tires
• Added a subwoofer
• Carbon mirror caps - factory black ones were damaged somehow
• Rexpeed side mirror glass - they shake at speeds over 50mph, do not recommend
  
  

 

[i3igpete]

• Rexpeed side mirror glass - they shake at speeds over 50mph, do not recommend

They might not be completely clicked in. I had that same issue on one side until I pushed harder and now the vibration is much less

 

[Danimal]

They might not be completely clicked in. I had that same issue on one side until I pushed harder and now the vibration is much less

It’s worse on the passenger side, so I’ll see if that’s the case. Thanks!

 

[itzTang]

It’s worse on the passenger side, so I’ll see if that’s the case. Thanks!

Mine is completely still. Just hope you didn’t break any of the clips on the back of the mirror. If you did it will shake.

 

[Danimal]

Mine is completely still. Just hope you didn’t break any of the clips on the back of the mirror. If you did it will shake.

Last I checked they were fine. It’s easy to remove the glass (suspiciously easy…) so perhaps it’s not fully seated. Thanks for the feedback!

 

[i3igpete]

The Rex speed clip is much more delicate than the factory one with only about half the attachment points around the edge of the Ring.

 

[Decentness]

Just installed the AA Catted Downpipe with the AA high flow cat today. Installed the Dinan Carbon fiber cold air intake with carbon inlet about 5 days ago.

Definitely helps give a little more turbo noises, but part of me kinda wished I went Armaspeed for the intake/inlet tbh, but I'll try without the box lid in the coming days and see if that increases the intake sounds.

Both pieces were great quality and no real issues installing, aside from DP just being a pain in the butt to connect and remove from the mid pipes. Car is a 24' with about 5k miles, for reference.

Only driven about 15 miles on DP, but no check engine light so far!

 

[jmikes]

put on A90shop's FI Exhaust catless downpipe. Nice easy install, granted I had somebody lend me an extra set of hands.

I'm quite fond of actually being able to hear the exhaust now. Zero drone, not very loud at all unless full throttle, and only a tad louder than stock when idle.

Put ~150 miles on it (did a short road trip right after) and no CEL.

 

[Wyrmhole]

Buffed out my tail-light scratches and saved myself 150 bucks!

 

[BMWAF]

Buffed out my tail-light scratches and saved myself 150 bucks!

Looks great. What was you method and what did you use? I have some plastic interior bits on my daily that need some love.

 

[Wyrmhole]

Looks great. What was you method and what did you use? I have some plastic interior bits on my daily that need some love.

Sanded out the scratches using an orbital: 240, 1200, 2000, 3000 grit sandpaper. Polished afterwards with chemical guys v38 & v32 compound. Not sure if this method works for interior bits tho