Ryan’s ‘23 A91MT Burnout - Slow Build

[RyanA90]

Here she is paired with the Dinan intake.

Sponsored

 

[indymajor]

I have an A91MT in CU Later and just purchased a lot of the carbon bits from Dinan. Intake, Inlet, Engine Cover, front lip, defuser, side skirts, hood vent inserts, mirror caps (wish they were not just covers) and the smaller duckbill type wing. Im also trying out the Dinantronics X piggyback system as Im not ready to ship my DME over the pond. Doing the HKS adjustable springs to keep the electronic control system and the HKS blowoff valve. Last but not least is the Active Autowerkes catted DP. Should be complete by 7/20 and I cant wait.

how do you like the Dinan Intake, the weave and craftsmentship look amazing but how do you like the performance?

 

[RyanA90]

I have an A91MT in CU Later and just purchased a lot of the carbon bits from Dinan. Intake, Inlet, Engine Cover, front lip, defuser, side skirts, hood vent inserts, mirror caps (wish they were not just covers) and the smaller duckbill type wing. Im also trying out the Dinantronics X piggyback system as Im not ready to ship my DME over the pond. Doing the HKS adjustable springs to keep the electronic control system and the HKS blowoff valve. Last but not least is the Active Autowerkes catted DP. Should be complete by 7/20 and I cant wait.

how do you like the Dinan Intake, the weave and craftsmentship look amazing but how do you like the performance?

Curious how that Dinantronics works compared to JB4. I love the premium quality of the Dinan intake.

Performance wise throttle response feels a little better than the CTS intake that I had before it. I’m guessing since it runs a bit cooler in the enclosed box. I only wish it was louder.

 

[RyanA90]

Today I had to remove a section of the scrape guard I have under my front lip and before I put my car back down I found this bad boy and unscrewed it. (-.1 whp)

It left a nice looking hole:

Poured some water on it, luckily its not leaking air! Glad it was in the meaty part of the tread.

Its good to always check your tires when you have the car up.

THE END.

 

[RyanA90]

Will be installing these bad boys later today:

 

[Jmanlevan]

Today I had to remove a section of the scrape guard I have under my front lip and before I put my car back down I found this bad boy and unscrewed it.

It left a nice looking hole:

Poured some water on it, luckily its not leaking air! Glad it was in the meaty part of the tread.

Its good to always check your tires when you have the car up.

THE END.

What are you using for a scrape guard?

 

[RyanA90]

What are you using for a scrape guard?

Amazon- Highly recommended and saves me everytime!

https://www.amazon.com/gp/product/B09BHSD9HN/ref=ppx_yo_dt_b_search_asin_image?ie=UTF8&psc=1

 

[Jmanlevan]

Amazon- Highly recommended and saves me everytime!

https://www.amazon.com/gp/product/B09BHSD9HN/ref=ppx_yo_dt_b_search_asin_image?ie=UTF8&psc=1

Thanks! I was looking into SlipLo’s but this is a way cheaper option!

 

[RyanA90]

Haven't taken any decent pics lately but here's a few in my garage of the APR Canards (+.7 whp):

 

[RyanA90]

Added the MKIV Supra Turbo emblem minus the Turbo on the CF engine cover (+.5 whp):

 

[RyanA90]

 

[Sharocks]

You rocking any spacers?

 

[RyanA90]

You rocking any spacers?

Yup check 1st page for info.

 

[RyanA90]

Verus Caps (+.2 whp):

 

[RyanA90]

Since @THOOPRA asked here's a list of exhaust I'm deciding on:

Top choice:
-Garage Whifbitz Full titanium exhaust (Best bang for the buck dual valved Ti exhaust and not Chinesium)

Would also consider:
-. HKS Turbo muffler (bc HKS lol)
- REMNANT PERFORMANCE LEVIATHAN (excellent price point but would love for it to fit my Kenji DP)
-Other dual set up with at least 3" id piping thats not Tomei lol

Maybe a single exit:
-RKti Signature ( no cutting needed to the diffuser)
-Sp1r (maybe)

Sponsored