Search results

I have tpms sensors 0n my track rims/ tires. It reads the tire pressures and tire temps fine. One point when you start at 27 PSI on track tires and turn off traction control it will turn it back on on the first lap until they get to about 30 psi. I have not figured out go to change the low...

That looks good on the trunk support. Not sure if you changed the trunk stops to solid ones as that is where the downforce will transfer the most from the trunk. Now you need a front splitter and drive planes?

So I use a solo 2. No ecu data but still gives you a lot data if you use their software and then down load the sessions. I also have a my Laps transponder. Have the track addict paid version but aways forget to bring phone and start as I have the other two going all the time. I am not...

So I can ad that those are solid numbers. It depends a bit on tires as most of the track tires like camber closer to -3 as a min. But I have been at -2.8 front and -2.6 rear and is pretty good. On toe I have run 0 in front but the 1 degree toe in makes it turn in better very responsive, so if...

I was traveling so have been out of touch. No worries. Feedback is always good so will adjust my commentary as well as I think we have started a good exchange and sharing. It is not about who fastest or best driver etc. we are all still learning. Especially me as I am a relatively knew to the...

If you guys are interested in seeing howthe car has been performing in TT. Just look at the NASA az region TT results. You will see it there. And can give you a relative comparison to the other groups

So you just need to get faster corner exit speed and make up for hp to get a run on them?go a little deeper straighten out Line across the apex and get on full gas before apex.! Hence brakes tires and suspension ! Easy to say hard to do and get car set up so it will do this as they are tail...

Well personally I would love to get it tt4 as most of the cars in my group are also full on race cars on slicks. Which I have not gone to. So is difficult to place in top 3. But again we are all out for the same plastic trophy so is just good fun. Not professional race group. Maybe later with a...

Yes I think razor lab is spot on and that is the result. So may not be for everyone. I would caution again getting to that 20pi setting you will blow the turbo if you run it hard and as much as I do. So look fir other stuff and back it if and you will be much safer in terms of longevity.

No no tuning. Stock. I know there could be a little risk on 30% ethanol but from all my race buddies and little bit of reading up it has the high pressure fuel pump with the new B58 and can handle. No lean codes etc. Plus is cheaper Race gas than mixing 100 oct. Runs cooler etc. I do have all...

No it us not stock but no jb4 tuner or additional boost. So has a catless down pipe, armytrix exhausts, cold air intake and charge pipe. Plug gap a. 20 and am running 30% ethonol. Oh forgot vargas oil cap breather(lol) That is it. And based on other cars etc I am fairly confidant. It us not...

Here us the Dyno sheet. I do not think I thet. even look at crank hp on a NASA Dyno?

That is where I got the vented fender as well.

Perfect just orders saber ones

If you are talking the connection by the turbo with the silver c clip you should be able to see if the tabs went down in the grooves 3 of them if I recall correctly. It does take some wiggling to get the o ring pushed all the way on. If you have the air box off can get down there with a light...

Welcome. Break it in. Take to the track!

It is really nice that everyone is sharing pics and doing all this cool stuff to your cars. That us what it is all about enjoying and working on my them and having fun. Big boy toys! I see at least one new potential track addict jumped in, so if you are new do not be afraid to jump in with what...

This is great. Where are the vents from. As that may be be next on my list.

yes - have that also so yes helps a bunch.

Thanks for the pic. I was looking at the top fender vents but wondered how to get that open so let us know how it works. Now just have to cut another whole in hood and get a good vent. I also found the 4' grinder with a cut off wheel does wonders on that plastic vs a small Dremel.