Search results

Fresh And Clean

I don't think it's an issue really because odds are if you get a flat you're just gonna pull over and get a flat bed anyway. Besides the rear tire, you will need a jack too. I can't envision anyone jacking their supra up in the grass on the highway or side road to change the tire. Car comes...

SOLD

Price Drop $90.............................

If anyone is interested, there's an autocross event in Concord next Saturday 7/25. It's a great way to push your car and find some of your limits, and the car's limits. Venue is large and asphalt is clean, so it makes for an outstanding location. If it's your first time, you can run Novice...

@Nocturnal LE what is your start up screen now? I have almost the same ones marked as you and didn't have any changes on startup screen. I think there might be a setting that was overlooked possibly? Did you go into Expert Mode at all? There is a startup animation selection that might have...

So will the 20's be stuck to aftermarket tunes or can they get flashed to 21's by the dealer?

Totally agree that the door edge guard is much less conspicuous and same price range. You wouldn't even know it was there. I would try that over the floor molding. I've been using the door edge guard for months and forget that it is even there as it blends in easily with the car.

Need to clean the barrels

Congrats and welcome! Now the next step is deciding on which mod you want to try first?

Barcode pulled this from Lowes FLEXCO 4-in W x 4-ft L Black Dahlia Thermoplastic Rubber Wall Base https://www.lowes.com/pd/FLEXCO-4-in-W-x-4-ft-L-Black-Dahlia-Thermoplastic-Rubber-Wall-Base/3094457

Yeah, it's definitely good stuff and opens the window for improvement and modding the system to one's particular taste. I'm glad Bavsound did post up to show that it isn't as bad as some people might anticipate it being. If someone was reluctant on doing any of the mods mentioned, I would say...

Video is good but in the video above the aluminum crossbeam (tranvserse pipe) that goes across the back of the car is missing. This will need to be removed and reinstalled too in order to get the upper quarter panel reinstalled. There is no way that you will get the upper rear quarter panel...

> Reinstall Subwoofer Rear Decking > Reinstall Rear Deck Lid Covering Battery > Install Net And Adjust As Needed > Tip: You Can Pull The Outer Edge Elastic Strap And Tie Off If You Want To Tighten The Net Down > Install Bungee Cords As Needed > Install XL Soft Loop On Bag Hanger Hooks...

> Using Allen Wrench, Install (1) Bolt, (1) Washer, And (1) Lashing Eye On All Four Corners > Tip Tighten Lashing Eye If You Want To Lock In Place. You Can Also Leave Semi-Loose If You Want It To Swivel.

> Carpet Holes Should Now Line Up With Bolt Housing. You Should Be Able To See Threads.

> Remove The Rear Deck Lid Covering Battery > Remove The Four Bolts Under The Carpet > Using The Marker Spot As Your Guide You Will Need To Cut A Hole In The Carpet For The Bolt To Go Through Caution: To Not Cut The Hole Bigger Than Needed For The Bolt To Go Through. Also Be Sure To Not...

> Reinstall Rear Deck Lid Covering Battery Into Trunk Of Car > This Will Help The Carpet Get Aligned > Take A Piece Of Painters Tape Or Masking Tape And Place On Top Of Carpet > Using A Marker Feel Around And Mark The Exact Location Of Bolt Underneath The Carpet > This Will Be Your...

> Pry Up Edge Of Carpet To Reveal Bolt Locations On Four Corners > While Holding Carpet Up, Thread All 4 Bolts Into The Locations > Do Not Thread The Bolt All The Way Down Flush > Leave Approx ½ Inch Sticking Up > You Will Use This As A Marker For Where To Cut Carpet

> Remove Rear Subwoofer Deck > Pull Back Subwoofer Deck Towards Rear Of The Car > Deck Is Held In Place By Pressure Clips Which Will Unsnap When Pulled