What did you do to your Supra today?

[J29DB03]

Any link and guide for those puddle lights?

https://www.supramkv.com/threads/how-to-install-puddle-lights.10112/

 

[Deighvid]

Bruh.... When I did my spring install the fronts were legit like 30 mins total. The rears took about 4 days because reassembly was a pain in the dick. The damn hub swivel hole just would not line up for the life of me and I ended up stripping the factory bolt and had to source another. Do you undo the sway bar when doing this or something? Even after getting the new bolt, I still couldn't get that damn thing to line up easily at all.

The rear took me forever too. I fucked with the jack and used a pry/flathead to line up half then push in the other half and full send the impact gun when it was close enough

 

[Valhariel]

i went in a spending frenzy on the Supra!

Spend a total of $3 for those to replace the gray plastic one that came with the wheels

please don't judge the dirt, i'm going to clean her right now

 

[BadOne]

Installed the Bavsound Subwoofers. They sound drastically better already and they are still in the 12 hour break-in period.

Pro tip for those considering it:

Go ahead and remove the crossbar before trying to remove the lower trim piece.
It'll take less time than trying to articulate the piece around it. I only realized this after installing the speakers.
Also, the bolts holding down the crossbar we're pretty loose...they are not anymore

 

[Sereph102889]

The rear took me forever too. I fucked with the jack and used a pry/flathead to line up half then push in the other half and full send the impact gun when it was close enough

Yea I was stupid and stripped the bolt on the first attempt. Luckily I found a replacement at Ace Hardware and was able to get the car back together in just a few days. I was more careful and did make sure to use a prybar on the second attempt lol. The Prybar was the key.

 

[CUL8RSAM]

All I did with Supra today was daydream about it...

Me at one hour after I put my deposit for the manual supra.

 

[JDG520]

Installed the Bavsound Subwoofers. They sound drastically better already and they are still in the 12 hour break-in period.

Pro tip for those considering it:

Go ahead and remove the crossbar before trying to remove the lower trim piece.
It'll take less time than trying to articulate the piece around it. I only realized this after installing the speakers.
Also, the bolts holding down the crossbar we're pretty loose...they are not anymore

worth the money? This is interesting, first I’ve heard about this option.

 

[SD_MK]

Did a blacked out Supra badge install today on the A91 soo it's all blacked out like the yellow, annnnd theeeee changed out the hood vents to actual vents, Suprastar CF. ??

 

[Vuns'sA91CF]

Burger motorsports. They are real nice too and have new bolts with them.

https://burgertuning.com/products/2020-toyota-supra-burger-motorsports-wheel-spacer-kit-w-10-bolts

Hey Thanks man, my apologies for the late reply. I may go with these spacers

 

[BadOne]

worth the money? This is interesting, first I’ve heard about this option.

Definitely worth it in my opinion. Here's the frequency response curve for the subs compared to the factory ones.
Note that sound doubles every 3dB.

 

[Mimosa]

Cleaned all the damn NC pollen out from under the hood. This is probably the last picture of this engine bay in its current configuration.

 

[Valhariel]

Cleaned all the damn NC pollen out of my engine. This is probably the last picture of this engine bay as it is now:

super clean and simple

 

[tadda]

I got a nice rock chip / spider crack in my windshield while on the I10 in Tucson today...Yup, that's gonna spread!

Scheduled an appt for Monday with Safelight for repair...$138

 

[Kiske]

Had the engine cover cut.

2/10 Purples don't match.

What did you end up redoing on the methanol kit's plumbing? Clearance issues?

 

[zrk]

2/10 Purples don't match.

They do not. By design. I had to buy all of it sight unseen, but I was hoping they'd contrast enough. I think they do in person, but I could always swap out the downstar bucket for a different color.

What did you end up redoing on the methanol kit's plumbing? Clearance issues?

Removing the second nozzle. I was running 2 500cc nozzles 30/70 water/meth, now I'm running 1 500cc nozzle with M1.