What did you do to your Supra today?

[Insomniac]

Ordered her a Seibon MB front lip. I think I am waiting on like 7k of cosmetic items ?.

Richard

 

[JRedMKV]

That key chain looks great ?
Where did you get it from ?

Here’s the link:
https://autoaddictz.com/products/alcantara-leather-supra-keychain

 

[Sbkhoun]

Hard wired my dash cam and my new wireless phone charger .

 

[ta70raiii]

Hard wired my dash cam and my new wireless phone charger .

What are the colorful items around the shifter?

 

[kaj]

What are the colorful items around the shifter?

Flair?. ?

 

[PikkaGTR]

Tucked her in for the night after she was outside most of the day
Had the Golf inside as I spent almost 8 hours on prep/paint correction and clay + a full car ceramic coating
Who says you can't pamper a Daily ?
I am pooped and need me a well deserved alcoholic beverage

 

[SupraSa1yan]

When did intakes get soo small in cars? ?

 

[SupraYYJ]

I hate to be the bearer of bad news, but I think there's something very wrong with your resonator.

What did this do to the sound?

 

[SupraSa1yan]

I do hear more spool, but not sure if its cause of the delete of the resonator or ots tune i added along with the delete/mod. Have not had anyone try to rev it for me to hear either.

Also not sure about adding hot air+ weird air flow in the box now... had it laying around so thought i'd slap it on.

 

[Kmj442]

installed my rear sway bar finally (and front but that took 30 mins so hardly notable)...Just waiting on the new bolts/nuts to replace the subframe/suspension bolts that are supposed to be replaced after removal

 

[zrk]

When did intakes get soo small in cars? ?

This is going to catch extremely hot air from directly above the turbo.....

 

[suicidaleggroll]

installed my rear sway bar finally (and front but that took 30 mins so hardly notable)...Just waiting on the new bolts/nuts to replace the subframe/suspension bolts that are supposed to be replaced after removal

Do you have part numbers for those bolts?

 

[Kmj442]

Do you have part numbers for those bolts?

I used the cusco manual for the parts:
https://cdn.sanity.io/files/16fc9m9h/production/4bdbc61d4763a5aa3ddb82332c50f73fb156ef70.pdf

 

[Kmj442]

I used the cusco manual for the parts:
https://cdn.sanity.io/files/16fc9m9h/production/4bdbc61d4763a5aa3ddb82332c50f73fb156ef70.pdf

I currently have everything connected again but still up on the quickjack waiting to replace 1 by 1. they SHOULD be here today

Edit: they may not be here until later this week...how bad of an idea is it to drive a little bit with the old bolts (I suspect it SHOULD be fine as long as torqued to spec) until the new ones come in. I just want to make sure theres no clunking or anything and this would give me a good chance to check before I get back under to replace them.

 

[krumpir]

Went to Thunderhill East w/ Bypass on Sunday with NCRC. Was 95° at the peak heat so wasn’t great on the pads and tires. Brake fade was real on stock pads and were by far the limiting factor, followed by tires, then the suspension. Also my HKS exhaust had the tips burn in a lot more and it melted my diffuser

Swapped from my TE37/MP4S setup to OEM for the track day. Will get proper track wheels/tires, looking at 18x10.5 with 295 square. Ohlins are going on also in two weeks.

Setup:
- Stock wheels, tires, pads
- Swift springs
- Motul RBF600
- HKS exhaust
- Motorsport Hardware lug conversion

PB was a 2:12, optimal on my Garmin said 2:10