What did you do to your Supra today?

[Rocksandblues]

made a short clip for Youtube

 

[MoTeC_R]

I added the carbon hood vents from the A90 shop. Also added the carbon fiber front and door trim which looks much nicer than I anticipated. Glad I chose this over the TRD door garnish. Saved $3500 with results I am very happy with. I didn’t take a picture of the carbon hood vents as everyone has seen them 1000 times.

Here’s the others:

 

[Awales74]

made a short clip for Youtube

Danny Ric, Mexico, 2022

 

[NFamous60]

Good thing you aren’t hurt dude that’s most important!!! Hopefully damage is minimal

Your right ?? I was trying to upload the video idk why I have a hard time getting them on here, but the way the bk slide out and car spun I ended up on the interstate in the slow and had to like Thurston the car forward bk into the median to get out the way. Didn't even think to chase his ass down for his plate number or something I was way to concerned about damage to the car. So far seems all good no broken panels, no rash or rock damage, just dirt everywhere gonna lift the car up and check under there as well.

 

[starman]

made a short clip for Youtube

I love VIR! Had a Blast driving my Supra there! I will say, the stock brakes were only good for a few laps before I noticed performance degradation. Will need to swap out to better pads next time.

 

[starman]

I added the carbon hood vents from the A90 shop. Also added the carbon fiber front and door trim which looks much nicer than I anticipated. Glad I chose this over the TRD door garnish. Saved $3500 with results I am very happy with. I didn’t take a picture of the carbon hood vents as everyone has seen them 1000 times.

Here’s the others:

I'd get those just so that the area can dry up quicker after a wash. Those OE "honeycombs" design make it hard to dry out in that area.

 

[razorlab]

I'd get those just so that the area can dry up quicker after a wash. Those OE "honeycombs" design make it hard to dry out in that area.

Leaf blower works wonders.

 

[FuzzyRev]

Leaf blower works wonders.

https://doublekindustries.com/challengair-dryers/dry-cycle-portable-motorcycle-automotive-dryer/

I've been rocking this thing for twenty years now. It was well worth it back when I had my bikes...it's worth it ten times over now that I own this car!

 

[razorlab]

https://doublekindustries.com/challengair-dryers/dry-cycle-portable-motorcycle-automotive-dryer/

I've been rocking this thing for twenty years now. It was well worth it back when I had my bikes...it's worth it ten times over now that I own this car!

yea, or one of those. I recently bought a Chemical Bros blower since my leaf blower was a bit big to navigate with easily in my garage.

However, since it's smaller it emits a F'in super high pitched whine. I have to wear earplugs to use it for any amount of time over 3 seconds. It works well though

 

[BadOne]

made a short clip for Youtube

POV you're Max Verstappen

 

[ope_sry]

Rexspeed windy things finally arrived, they must be manufactured with a gold core, I cannot otherwise rationalize the price.

ZL1 rock gaurds installed for my stance boi 18mm/20mm spacers. Also did a Motorsports Hardware stud conversion with their gunmetal lugs. Pleased with the look while I’m still on gross oem wheels.

Had an alignment scheduled at Toyota this evening (installed Eibach springs this weekend) but once I arrived they informed me they couldn’t get it on the alignment rack because I was too low ?. I’ve already found a reputable shop that accommodates such obscenely modified vehicles so no worries there!

 

[RyanA90]

Rexspeed windy things finally arrived, they must be manufactured with a gold core, I cannot otherwise rationalize the price.

ZL1 rock gaurds installed for my stance boi 18mm/20mm spacers. Also did a Motorsports Hardware stud conversion with their gunmetal lugs. Pleased with the look while I’m still on gross oem wheels.

Had an alignment scheduled at Toyota this evening (installed Eibach springs this weekend) but once I arrived they informed me they couldn’t get it on the alignment rack because I was too low ?. I’ve already found a reputable shop that accommodates such obscenely modified vehicles so no worries there!

Nice! what length studs did you get and any rubbage?

 

[ope_sry]

Nice! what length studs did you get and any rubbage?

No rubbing yet that I’ve noticed after a couple hundred mostly highway miles.

here’s my order, those studs accept up to 20mm spacers. I like to live on the edge.

 

[R6chan]

made a short clip for Youtube

About 2:12 at Full Course is pretty good man with all that traffic! VIR is my home track and favorite..

what tire/suspension/brake setup you running. What top speed you hitting in the back straight!?!

 

[Rocksandblues]

About 2:12 at Full Course is pretty good man with all that traffic! VIR is my home track and favorite..

what tire/suspension/brake setup you running. What top speed you hitting in the back straight!?!

had some 2:09s. Car can do 2:05 2:03 with better driver . Doh
Only my second time there. I need to trust the car more in 10 and through hog pen
55 cars in my group! Never really got clean lap and I wish I could have followed some vets
275 square, stock dampers just stiffer springs (need real suspension)
Csg brakes and 650 fluid

was hitting 155 on back. But again still tip toeing and not 100% confident in the absolute braking point

lots to learn there!!