What did you do to your Supra today?
- Thread starter Ryanthetemp
- Start date
- Watchers 564
lowlife
Active Member
- First Name
- Justin
- Joined
- Jun 4, 2020
- Threads
- 1
- Messages
- 29
- Reaction score
- 43
- Location
- Kenosha, WI
- Car(s)
- 2020 Supra, 2004 VW R32
Removed my downpipe and started working on my vent gauge install.
lowlife
Active Member
- First Name
- Justin
- Joined
- Jun 4, 2020
- Threads
- 1
- Messages
- 29
- Reaction score
- 43
- Location
- Kenosha, WI
- Car(s)
- 2020 Supra, 2004 VW R32
Finally finished this up and got it installed. P3 gauge mounted in rivers vent
ercarlson8
New Member
- First Name
- Erik
- Joined
- Jul 16, 2020
- Threads
- 1
- Messages
- 2
- Reaction score
- 0
- Location
- Glendora, CA
- Car(s)
- 2020 Supra
12.5 front? where did you purchase?Installed 12.5mm ECS and 15mm Turner wheel spacers today....very pleased with quality and fitment
Love the look of the wider rear stance!
wolf_kyle
Well-Known Member
This is more of what ive done throughout the week.
- red push button start
(https://www.ebay.com/itm/Engine-Sta...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2648)
- wrapped the roof gloss black
- wrapped the side door garnish matte black
- gray banner (might go matte or gloss black) with cut out for the sensors
- new paddle shifter extensions (aluminum)
(https://www.ebay.com/itm/Black-Stee...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2648)
- red push button start
(https://www.ebay.com/itm/Engine-Sta...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2648)
- wrapped the roof gloss black
- wrapped the side door garnish matte black
- gray banner (might go matte or gloss black) with cut out for the sensors
- new paddle shifter extensions (aluminum)
(https://www.ebay.com/itm/Black-Stee...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2648)
akasonny
Well-Known Member
- First Name
- Steven
- Joined
- Mar 25, 2020
- Threads
- 5
- Messages
- 220
- Reaction score
- 86
- Location
- Sahuarita, AZ
- Car(s)
- 2020 Supra Premium (Downshift Blue)
I'd love to find someone in my area to do what you've done.Finished the engine bay (hydro dipped the cusco strut brace) and had carbon fiber hydro dipping done to the aluminum cross brace behind the seats to get rid of the bright aluminum on the interior.
akasonny
Well-Known Member
- First Name
- Steven
- Joined
- Mar 25, 2020
- Threads
- 5
- Messages
- 220
- Reaction score
- 86
- Location
- Sahuarita, AZ
- Car(s)
- 2020 Supra Premium (Downshift Blue)
I've been wishing for that too...so far, nada.
Nonschlont
Well-Known Member
Do u happen to do any logging of temps? Daily cruising and WOT. Would be awesome to have a before n after! I'm very interested to see some real world results if there's any benefit for a mildy modded daily. As sensitive as these cars are to keeping temps within a certain range, I would imagine every bit helps.CSF heat exchanger
a90moe
Well-Known Member
My reply in the CSF thread:
Ambient temps and weather conditions have been very unstable lately (high humidty and high temps)
Tried to compare the closest runs possible since I did not have a lot of meth only pulls and wanted meth against meth + heat exchanger
Meth only
4th gear pull start @ 3.5K - 6.5K
Start IAT 52c
End IAT 58c
Meth + Heat exchanger
4th gear pull start @ 3.5K - 6.5K
Start IAT 51c
End IAT 57c
After comparing a few pulls I did not notice any reduction in overall IAT just like @Twisted Tuning mentioned however, IAT temp drop between runs is much faster after letting off and cruising. It is much better in recovery now
This translates into a more consistent performing car overall in the heat here which is an added bonus
It does help
Tsar
Well-Known Member
This pouch showed up today. 4 stickers inside, good for at least 40 horsepower.
