What did you do to your Supra today?

[Munkeeboi]

Spacers. 13f / 15r

Front before

Front After

Rear Before

Rear After

 

[AustinGRSupra]

I got my AIMGAIN wing painted, and appointment made for mounting next week at SoulSpeed Performance, Austin, TX.

 

[nebulous13]

I got my AIMGAIN wing painted, and appointment made for mounting next week at SoulSpeed Performance, Austin, TX.

Sweeeeeet. Mine arrived this week as well. Lip kit too. Gets installed next week.

 

[AustinGRSupra]

Sweeeeeet. Mine arrived this week as well. Lip kit too. Gets installed next week.

Nice, what are you doing for paint? Matching it? (You almost have to when you have nocturnal.)

 

[F1 Silver Arrows]

Micky Thompson 305's on factory wheels for later on in the year when I put her down the strip to see what she will do

Some shiny Versus bits along with diff cooler plate & turbo heat shield to be put on with my AFE intake when my Mishimoto catch can shows up

Getting used to the Boost Logic exhaust

Your car is eerily similar to Adam LZ's. Boostlogic exhaust system? Micky Thompson 305's in the rear? What's next a Pure 800 turbocharger? ;D

 

[Kiwi Greg]

Your car is eerily similar to Adam LZ's. Boostlogic exhaust system? Micky Thompson 305's in the rear? What's next a Pure 800 turbocharger? ;D

Had considered a Pure 800 but too much $$ & hassle to get it sorted over here, wasn't sure which tires Adam had

Also with my current relationship with the Dealership I can possibly swing a warranty claim if needed but with a bigger turbo I think I would be pushing it

 

[puzzled]

I envy those aluminum red oil filler caps! I want one too..

 

[mjonesjr8]

https://www.supramkv.com/threads/fuse-panel-layouts.5741/page-2

let me know how else i can help you out with

Great thank you!

 

[nebulous13]

Nice, what are you doing for paint? Matching it? (You almost have to when you have nocturnal.)

I’m matching the wing to nocturnal and doing the lip in satin black to match existing lip pieces.

 

[supbirdy]

Street Hunter #8 BEGINS! (Instagram: SUPBIRDY)

Welp, finally started posting videos on YouTube about my Supra build, figured I'd start here too!
http://youtube.com/c/kingsmustrise

 

[JRedMKV]

Hi guys. I swapped out my regular steering wheel for the red and black Launch Edition steering wheel and I added AutoTecknic carbon fiber shift paddles.

 

[a90moe]

Micky Thompson 305's on factory wheels for later on in the year when I put her down the strip to see what she will do

Some shiny Versus bits along with diff cooler plate & turbo heat shield to be put on with my AFE intake when my Mishimoto catch can shows up

Getting used to the Boost Logic exhaust

Changing the MST to AFE?

 

[Kiwi Greg]

Changing the MST to AFE?

Yes

 

[jchall30]

Hi guys. I swapped out my regular steering wheel for the red and black Launch Edition steering wheel and I added AutoTecknic carbon fiber shift paddles.

How was changing out the wheel?

 

[JRedMKV]

It’s a fairly straightforward job but it takes a lot of time and patience. I watched the Speed Industry video as reference to remove the steering wheel. After getting the wheel off then I needed to figure out how to remove the plastic piece that holds the electronics and that big plastic piece at the bottom of the wheel.

The FIRST thing that you need to do after removing the steering wheel is to remove both of the shift paddles by removing the torx screws. This will expose two more torx screws from the back of the steering wheel. Remove these two screws then you can carefully pull off the main plastic piece with all the switches. Also make sure to remove the connector for the electronics that’s on the right side. It’s difficult to pull off these pieces because they are held by 4 plastic tabs that go in these depressions in the pics I attached but just be careful and they will come out. Same thing with the lower plastic trim piece, just carefully pry off the whole thing. It’s held by 4 tabs. Once you get those off you’re pretty much home free. There’s two other electronic modules mounted inside the steering wheel housing that you need to remove but those are easy to pull out then you can easily remove all the wiring in one piece and transfer it to the new wheel.

I probably should have taken pics of the whole process but I really wasn’t thinking about making a guide. Hopefully these tips help you guys out.