What did you do to your Supra today?

[hotsaucewizard]

Are you pairing it up with their catless DP?

I’ve already got the titan motorsports one installed, I’ll put up an exhaust vid when I’m finished today.

Must be NICE (kidding congrats and those welds look amazing!) ... meanwhile i've been staring at this......

Ouch, that sucks. It really is a beautiful piece. Coincidentally their shop is only a couple of miles from where I live so I just drove over there and they gave me a tour of the shop as well. Some bad ass cars over there…

 

[starman]

Ouch, that sucks. It really is a beautiful piece. Coincidentally their shop is only a couple of miles from where I live so I just drove over there and they gave me a tour of the shop as well. Some bad ass cars over there…

I've had the worst luck with aftermarket bits this past month. The damaged muffler as listed earlier in this thread, I had fitment issues with Rexspeed v4 spoiler (more info here > https://www.supramkv.com/threads/a91-replica-spoiler.6962/post-137398) and I was sent Phantom Grey instead of Turbulence Grey IND reflectors as well.

Both the Rexspeed Spoiler issue and reflector have been resolved from the vendor though (finally received the correct color reflector a month later, and finally was able to return the spoiler for a refund).

Anyway, while not today, car was PPFd with XPEL a few weeks ago

 

[BA9092]

Full-screen Apple CarPlay! Huge thanks to Rob @EasyBimmerCoding

Also removed the plastic trim pieces from both ends of the rear aluminum bar. I don't mind the 2mm gap all around especially since nearly 80% of the squeaks and creaks are gone now! Need to clean up the finger prints though.

 

[Garni_Z]

Just went for a very spirited drive after the charge pipe and MST intake install. Holy hell the turbo noises that I'm hearing are making me giggle like a little child.

Also, if anyone can give advice please do. One of my MAF screw heads snapped off. The screw is in the intake pipe and part of it it still in the MAF sensor. It's very snug. Should I worry about getting it fixed now or only if an issue arises?

Just realized why the screwhead snapped off. MST didn't provide me with the 2 MAF sensor screws to replace the OE screws so I reused those. Didn't work well.

Hey man, I just ordered me a MST V2 intake with the turbo pipe and wanted to pull the trigger on the FTP chargepipe as well. It all fit together??

 

[Kamry]

new wheels!

 

[bajanstefan]

new wheels!

Looking good homie.

 

[zrk]

Hey man, I just ordered me a MST V2 intake with the turbo pipe and wanted to pull the trigger on the FTP chargepipe as well. It all fit together??

Yup. I have this setup. It’s all fine

 

[Pej1282]

I finally completed the last step of the sound system mod @tadda provided all of us with. I installed the dynamat in the trunk. I got the roll for $10 on Amazon via the “like new” section. All that was wrong with it was that the original package was a little beat up causing the price markdown

 

[hotsaucewizard]

Update: it’s not quiet

I have a few rattles in the trunk.. thinking it’s because I never finished the tadda mod… gonna go out and get a 2” hole bit and put that panel back on and probably smash some noico into the rear panel as well

 

[Andrew4Supra]

Added the last piece of ppf to the Supra yesterday (hatch area).

It’s finally completely covered in paint protection film from top to bottom.

 

[superd6199]

Added the last piece of ppf to the Supra yesterday (hatch area).

It’s finally completely covered in paint protection film from top to bottom.

You did it yourself?

 

[Andrew4Supra]

You did it yourself?

~ yes but with the exception of the hood. too large of a piece (72”x72”) for a one man show. ?

i’ve installed about 500 kits since the late 90’s

therapeutic to me in some weird way.

 

[superd6199]

~ yes but with the exception of the hood. too large of a piece (72”x72”) for a one man show. ?

i’ve installed about 500 kits since the late 90’s

therapeutic to me in some weird way.

very nice! That explains why you’re able to do it yourself. I was thinking of doing it myself but everyone told me it’s not that easy. Better off letting the pros do it.

 

[Andrew4Supra]

Very nice! That explains why you’re able to do it yourself. I was thinking of doing it myself but everyone told me it’s not that easy. Better off letting the pros do it.

Thanks!

Yes indeed not something I’d ever recommend doing without major experience. And you’re right the Supra is much more difficult than most applications.

And as I always say… “the product is only as good as the installer”. The end result is all about the installer.

I’m a perfectionist so… I wouldn’t trust many others with my personal car.

PPF when it’s new! Cheers.

 

[NcreAighStonH]

Dressed up the engine bay a bit today!!!

Where did you get the dress up bolts?