What did you do to your Supra today?

[Danimal]

Happened to me aswell.

Glass Part was cad $125 I reckon.

Should be lower in usd.

That makes me feel slightly better. Not the price, but that someone else is clumsy af like me.

I’ve not yet spent much time looking, but my cursory glance showed that the blind spot version of the mirror glass is $$$. Yours a premium with driver assist?

 

[Danimal]

 

[concept]

I bought a replacement passenger side view mirror for my wife's 20 year-old Lexus. It came with a removal tool and the replacement mirror subassembly which snaps in place. There was no need for me to install the heating wiring, since the ambient temps never go below 37 degrees. The cost of the mirror subassembly was about $18. A full mirror housing with mirror runs $500.

 

[Syeeee]

That makes me feel slightly better. Not the price, but that someone else is clumsy af like me.

I’ve not yet spent much time looking, but my cursory glance showed that the blind spot version of the mirror glass is $$$. Yours a premium with driver assist?

Yeah I have premium with driver assist. If I recall it has one clip for blindspot and those two little inserts you have to slide in.

But fortunely cheap part.

 

[mdpalmer]

Installed Rexspeed color matched mirror caps. Been wanting to do this since I bought the car 2 years ago ? Comparing before and after below.

 

[Got_M]

Got my ECU unlocked by Femto

Going MHD+ stage 2? Mine is at Femto right now. Should have it back sometime next week.

Contemplating using my JB4 charge pipe meth with it. I want to max out that stock turbo before I go spend thousands on port injection/turbo kit and trans build.

 

[TBK]

Going MHD+ stage 2? Mine is at Femto right now. Should have it back sometime next week.

Contemplating using my JB4 charge pipe meth with it. I want to max out that stock turbo before I go spend thousands on port injection/turbo kit and trans build.

BM3 for now. Custom tune a little bit later down the line. Will also have a catless downpipe and flex fuel kit going on later in the week, hopefully.

 

[Bug2th]

There are/used to be some aftermarket ones with a bluish tint that reduced reflections a lot that I think were a bit cheaper.

Had to replace my mirror caps because the passenger cap and a-pillar garnish seem to have been damaged by something that splattered on them - brake fluid? Who could have done that????? ? Definitely something I would do, so could have been me.

When removing the passenger side mirror glass, I broke it. Eff me, this is going to be expensive.

 

[BA9092]

There are/used to be some aftermarket ones with a bluish tint that reduced reflections a lot that I think were a bit cheaper.

Yup. I replaced mine with the Rexpeed ones. Love them! The fact that they're both convex helps with driver side blind spot too.

https://www.rexpeed.net/product/detail/1

 

[Danimal]

Yup. I replaced mine with the Rexpeed ones. Love them! The fact that they're both convex helps with driver side blind spot too.

https://www.rexpeed.net/product/detail/1

FINE, Rexpeed mirrors ordered. Being clumsy AF is expensive.

I also think that the 2 tutorials I found on this forum recommended a way to pry off the mirrors that will cause broken glass like 50% of the time. Don’t pry from the outside corner, folks, no matter what the well-written tutorial says. Pry from the bottom middle.

 

[itzTang]

FINE, Rexpeed mirrors ordered. Being clumsy AF is expensive.

I also think that the 2 tutorials I found on this forum recommended a way to pry off the mirrors that will cause broken glass like 50% of the time. Don’t pry from the outside corner, folks, no matter what the well-written tutorial says. Pry from the bottom middle.

I think most tutorials i found said to pry from the bottom ? makes more sense since the back attachment is in the middle and prying from the side is the long way, furthest from the back attachment ? well we make mistakes and learn.

 

[Supradawg]

Installed Rexspeed color matched mirror caps. Been wanting to do this since I bought the car 2 years ago ? Comparing before and after below.

How is the paintmatch in your opinion? Looks nice.

 

[Vertex]

Yeah, seriously! Everything is flawless on my side, guess I have to redo all the BimmerCode stuff? Also feels like the fake engine noise is back on? Will play around with it this weekend I suppose.

Yes you will have to re-code anything you had coded out/off. Anytime that is updated I believe it clears everything, same thing when the recall got done on my car I had to re-code everything and even go back through my equalizer settings

edit: saw your later response as I went through the thread and glad to hear everything is working to how you had it coded before

 

[rwense]

Made good progress on the hood vent I designed to replace the 777 GT4 style vent after it warped and cracked in multiple spots.

After I finish trimming, painting, and riveting it down I'll be printing a wicker to go with it.

 

[Timmy_Jones]

Yes you will have to re-code anything you had coded out/off. Anytime that is updated I believe it clears everything, same thing when the recall got done on my car I had to re-code everything and even go back through my equalizer settings

edit: saw your later response as I went through the thread and glad to hear everything is working to how you had it coded before

Strange! Seems it flip flopped. All good now