OEM Wind Buffetting Kit (Fin Front Ventilator)

[speedlimit]

I called up my local Toyota dealership and asked them to put in an order for the OEM wind buffetting kit that comes on the 2026 model. I had no issues putting in the order with a 2024 model year VIN.

I received a call back confirming he found some but they were technically discontinued so whatever stock they have left, that's it. Not sure how true that is but considering they were $6/each and he found them available, I picked up a few extra sets.

Part Numbers:
RH: 61197-14010
LH: 61198-14010

Sponsored

 

[splv]

Thanks for sharing. Please post up some pictures after installing.

 

[speedlimit]

Thanks for sharing. Please post up some pictures after installing.

It may be a hot minute since I need to figure out how to get the eBay ones off first without destroying the trim. I am not very optomistic about it ha.

 

[nanaisu]

It may be a hot minute since I need to figure out how to get the eBay ones off first without destroying the trim. I am not very optomistic about it ha.

If it's stuck on with 3m, fishing wire. 45~lbs works well. Make sure you wear a pair of gloves that you can easily slip off. Might need to make a sawing motion with the wire to break through the tape. Heat can help.

 

[speedlimit]

If it's stuck on with 3m, fishing wire. 45~lbs works well. Make sure you wear a pair of gloves that you can easily slip off. Might need to make a sawing motion with the wire to break through the tape. Heat can help.

Unfortunately I didn't think I'd ever be removing it so I used the X-Life BK that came with the kit. It "should" soften with heat.

 

[Link]

Thank you for sharing this information. Had this on my to-do list as well as finding part numbers for front spats on '26 models.

 

[johnsmither]

It may be a hot minute since I need to figure out how to get the eBay ones off first without destroying the trim. I am not very optomistic about it ha.

Nah take a hairdryer to it for a minute, and then slowly pry at it with a trim removal tool. You can do fish wire too but trim tool's good for getting in there and lifting it off.

 

[BMWAF]

Bruh. The EBay ones work perfectly and look a lot better than the Toyota afterthoughts. Why on earth would you bother?

 

[ericchen_ec]

Bruh. The EBay ones work perfectly and look a lot better than the Toyota afterthoughts. Why on earth would you bother?

$6 dolla is $6 dolla, but if they were actually discontinued he could easily sell to the right person for $20 lol

 

[Andrew4Supra]

These are the best looking ones and for $75… they look oem and clean. They can be found on eBay.

https://ebay.us/m/uxdlEA

 

[speedlimit]

$6 dolla is $6 dolla, but if they were actually discontinued he could easily sell to the right person for $20 lol

Lol it was more just in case they fly off or get damaged. Maybe in 10 years these will be the S2K hardtop for Supras

These are the best looking ones and for $75… they look oem and clean. They can be found on eBay.

https://ebay.us/m/uxdlEA

Those are the ones I have. They worked better than the door bumpers. For $6 and it being OEM, I'm just scratching a curiosity.

 

[BMWAF]

$6 dolla is $6 dolla, but if they were actually discontinued he could easily sell to the right person for $20 lol

Your math isn't mathing. $75+$6. I guess what I'm saying is that the EBay ones work, are already on his car and look much better than Toyota's crap. Nothing but Ls here.

 

[NitroBowl]

These are the best looking ones and for $75… they look oem and clean. They can be found on eBay.

https://ebay.us/m/uxdlEA

i got these same ones but carbon fiber from alibaba for $96

 

[J29DB03]

They’re not discontinued. By law they have to be available for at least 5 years after the model year.

 

[Kharry]

I just put in an order for $20. Fumbled a few weeks ago I could have had them for the $6 but oh well. The dealer did say it was discontinued.

Sponsored