What did you do to your Supra today?

[puzzled]

I installed that factory JDM cup holder cover thingie today. Contrary to what others have mentioned, the fit was snug as it should be and no issue. I also updated my car and her MAX360c to run my iPhone15Pro.. adjusted PSI and took her off Flatstoppers. Car is ready to run for the season.. first stop, I need to go for an emissions check.

Then will do a quick oil change and enjoy the drive until September.

 

[Andrew4Supra]

Oil and brake fluid change today at the local bmw dealer... ready for Spring!

I was able to inspect the underside as well... always keeping it clean.

 

[razorlab]

Revisited self-tuning my Supra since I have a little time before the track season starts...

 

[YukonSupra]

Super hard to tell since I have not seen those in person yet but am just about to order a set myself in smoked. They LOOK like they're the clear option but I could be mistaken.

Those are the smoked. I have the same set, and I can attest that they look FANTASTIC on the car!

 

[BA9092]

Those are the smoked. I have the same set, and I can attest that they look FANTASTIC on the car!

Same here. The smoked tails go really well with the smoked V2 F1-style reverse/brake light from OLM.

 

[Vertex]

Those are the smoked. I have the same set, and I can attest that they look FANTASTIC on the car!

I just ordered studs and titanium lug nuts last night. This morning I ordered the smoke heritage lights from OEM+ and some wheel spacers, magnetic drain plug, and then the front and rear badge kit with the wheel caps in matte black with red logo for my matte storm grey Supra with red interior. I think that will all look fantastic on the car

 

[YukonSupra]

I just ordered studs and titanium lug nuts last night. This morning I ordered the smoke heritage lights from OEM+ and some wheel spacers, magnetic drain plug, and then the front and rear badge kit with the wheel caps in matte black with red logo for my matte storm grey Supra with red interior. I think that will all look fantastic on the car

Some dirty shots from the garage after installing a bunch of stuff over the Easter Weekend.

 

[Evolution]

Prepping for my track day in Vegas this weekend. Rotated tires, pulled wheel studs and re-loctited them, nut and bolt check, updated trans tune to version 1.3 and made sure it still had oil in the engine. Brake pads are still looking good after 6 big track events and a few auto-x events. Going to wash it tonight and I should be ready to go!

 

[Vertex]

Some dirty shots from the garage after installing a bunch of stuff over the Easter Weekend.

Same color as my car too! I also have all the verus engine bay dressup stuff and the jack pucks as well.

What exhaust are you running? Almost looks like boost logic tips

 

[jtsang25]

I installed that factory JDM cup holder cover thingie today. Contrary to what others have mentioned, the fit was snug as it should be and no issue. I also updated my car and her MAX360c to run my iPhone15Pro.. adjusted PSI and took her off Flatstoppers. Car is ready to run for the season.. first stop, I need to go for an emissions check.

Then will do a quick oil change and enjoy the drive until September.

Any pictures/ vid? Maybe my set was faulty. If it's snug I'll buy another set while I'm in Japan.

 

[puzzled]

Any pictures/ vid? Maybe my set was faulty. If it's snug I'll buy another set while I'm in Japan.

Yeah, just a quick picture.. No looseness at all. ?

 

[Rocksandblues]

not much. Just sitting on trailer ready to go back to track

 

[lucky phil]

Yeah, just a quick picture.. No looseness at all. ?

Yes I have this and mine fits snugly.

Phil

 

[jtsang25]

Yeah, just a quick picture.. No looseness at all. ?

Yes I have this and mine fits snugly.

Phil

And you didn't have to push/force them in? Guess mine was a bad batch then.

 

[puzzled]

And you didn't have to push/force them in? Guess mine was a bad batch then.

Not forced in, just pushed in with some pressure.