Sponsored

Winter build log - looking for feedback/advice.

dAPEX

Well-Known Member
Joined
Nov 27, 2024
Threads
4
Messages
82
Reaction score
36
Location
Kansas City, MO
Car(s)
2024 Supra 3.0 6 MT, 2015 BMW m235i 6 MT, 1999 BMW M3 5-speed, 2013 BMW X3 35i
Current build:

- 2024 Supra 3.0 6MT
- MHD 93 octane stage 2 tune with MHD flexfuel kit
- Armaspeed "cold" air intake
- AWE track catback exhaust
- AA catted downpipe
- Rear differential brace
- Cusco power brace
- Ultra racing strut bar

Winter build parts purchased:

- DAW gen 2 Ultraflow X
- Dorsch DS25/350
- S58 injectors
- Project gamma intake manifold
- Uniclutch track
- BMR catch can
- Visconti valve cover with PCV upgrade

I got a deal on the valve cover PCV upgrade so went ahead and purchased it but I'm not sure if it is the best option since I also have the BMR catch can kit. Would it be better to do a PCV delete and vent to atmosphere or use the Visconti valve cover?

The Dorsch DS25/350 that I purchased was for a 2 series so I think I need a couple different pieces of hardware (hard fuel lines are slightly different shapes on our car). I emailed Dorsch to find out if those parts can be purchased separately.

Is anyone else running a similar setup? Any recommendations for a turner for this set of hardware. I would prefer to stick with MHD.

I'm in the Kansas City, MO regional near the airport. Any good shops for installation and tuning near me? Would prefer to stay on MHD platform for now.

Currently, I daily drive the car in all seasons including snow and winter. Hoping to make it a little more capable and exciting while maintaining as much of the factory feel of the tune with gradually increasing torque that can maintain fairly flat to redline and a HP curve that continues to ramp up as we get into the upper rev range. Mostly doing spirited driving around like with some occasional autocross events, probably do one or 2 events driving.

Hopping for a reliable 600-650 WHP and 600 wheel torque. I would like to find a tuner who can get me a gentle roll on the torque and then flatten the curve for the rest of the rev range with HP gradually building towards midline. Anyone have a recommendations for a MHD tuner who has tuned with these particular parts.

Any other things I should just do while I'm in there? Any other upgrades needed to make this work? Koilovers? Different wheels/tires? Axles or driveshaft?
Sponsored

 
Last edited:

CERIALPHREAK

Active Member
Joined
Sep 1, 2026
Threads
1
Messages
44
Reaction score
21
Location
Chicago
Car(s)
2024 3.0 Premium MT
Might be worth a clutch upgrade if you're still on stock. My tune shop mentioned the clutch may need to get swapped out past 500 ftlbs.

Edit: Nvm didn't see you're already doing it, reading is hard.
 
Last edited:

Timmy_Jones

Well-Known Member
First Name
Tim
Joined
Jan 8, 2023
Threads
64
Messages
1,418
Reaction score
1,613
Location
NH
Car(s)
23’ 3.0 Base
Driving in snow and winter? Scrap the whole build. Get dedicated wheels and snow tires along with the best fluid film undercoat you can. Or find a winter beater.

All this power on an MT is going to be more expensive than you or a shop (unless extremely dedicated and having already done a similar build) thinks. Especially with some of your questions. You absolutely need a top tier shop to help
 
OP
OP
dAPEX

dAPEX

Well-Known Member
Joined
Nov 27, 2024
Threads
4
Messages
82
Reaction score
36
Location
Kansas City, MO
Car(s)
2024 Supra 3.0 6 MT, 2015 BMW m235i 6 MT, 1999 BMW M3 5-speed, 2013 BMW X3 35i
Current build:

- 2024 Supra 3.0 6MT
- MHD 93 octane stage 2 tune with MHD flexfuel kit
- Armaspeed "cold" air intake
- AWE track catback exhaust
- AA catted downpipe
- Rear differential brace
- Cusco power brace
- Ultra racing strut bar

Winter build parts purchased:

- DAW gen 2 Ultraflow X
- Dorsch DS25/350
- S58 injectors
- Project gamma intake manifold
- Uniclutch track
- BMR catch can
- Visconti valve cover with PCV upgrade

I got a deal on the valve cover PCV upgrade so went ahead and purchased it but I'm not sure if it is the best option since I also have the BMR catch can kit. Would it be better to do a PCV delete and vent to atmosphere or use the Visconti valve cover?

The Dorsch DS25/350 that I purchased was for a 2 series so I think I need a couple different pieces of hardware (hard fuel lines are slightly different shapes on our car). I emailed Dorsch to find out if those parts can be purchased separately.

Is anyone else running a similar setup? Any recommendations for a turner for this set of hardware. I would prefer to stick with MHD.

I'm in the Kansas City, MO regional near the airport. Any good shops for installation and tuning near me?

Currently, I daily drive the car in all seasons including snow and winter. Hoping to make it a little more capable and exciting while maintaining as much of the factory feel of the tune with gradually increasing torque that can maintain fairly flat to redline and a HP curve that continues to ramp up as we get into the upper rev range. Mostly doing spirited driving around like with some occasional autocross events, probably do one or 2 events driving.

Hopping for a reliable 600-650 WHP and 600 wheel torque. I would like to find a tuner who can get me a gentle roll on the torque and then flatten the curve for the rest of the rev range with HP gradually building towards midline. Anyone have a recommendations for a MHD tuner who has tuned with these particular parts.

Any other things I should just do while I'm in there? Any other upgrades needed to make this work? Koilovers? Different wheels/tires?
Might be worth a clutch upgrade if you're still on stock. My tune shop mentioned the clutch may need to get swapped out past 500 ftlbs.

Edit: Nvm didn't see you're already doing it, reading is hard.
Reading is hard and I was sleeping when I wrote this so it may or may not make sense. Clutch is going to be done in a few days.
 
OP
OP
dAPEX

dAPEX

Well-Known Member
Joined
Nov 27, 2024
Threads
4
Messages
82
Reaction score
36
Location
Kansas City, MO
Car(s)
2024 Supra 3.0 6 MT, 2015 BMW m235i 6 MT, 1999 BMW M3 5-speed, 2013 BMW X3 35i
Strongly recommend returning the project gamma manifold and visconti valve cover immediately
I hadn't heard bad things about the project gamma manifold - what are your thoughts on that and the Visconti valve cover. That purchase was more of a whim and I admit I didn't do my research on it before hand. Figured I got a good deal and if I don't use it I can sell it without a loss. Thanks!
Sponsored

 
 








Top