What did you do to your Supra today?

[Loco38SUP]

Could you provide specs on those rear Blitz bolts? Would like to buy similar ones to use on a 2020.

I don’t, mine are installed on my car. Maybe @nosavingthrow can help out since he didn’t install them.

-RJM

 

[SupraCal]

Sure do, its M10 x 1.5. I checked it
on my thread gage and verified it with my die set.

-RJM

thank you very much!
Do these screws come in different lengths?

 

[Munkeeboi]

Could you provide specs on those rear Blitz bolts? Would like to buy similar ones to use on a 2020.

Where in So cal are you? I have a spare set since I tapped the rear holes to M10 x 1.5. I can give you the bolts or tap the holes for you if you are local.

 

[obito]

How do you guys feel about solely installing a front lip/diffuser if it's not too loud/extra? Since the Supra already has side skirts/rear aero pieces I feel like it wouldn't look out of place, as opposed to other cars where you would want to balance the remaining parts. Would it look odd at stock ride height?

 

[jbretthorton]

Installed Powerstop Z16 pads all around, Replaced the stupid "Clown Horn" with the addition of the low tone horn. Mucho better! Installed Zl1 Add-on Rock Guards.
Drove the ol girl to start breaking in the pads.

 

[MyCorolla]

Where in So cal are you? I have a spare set since I tapped the rear holes to M10 x 1.5. I can give you the bolts or tap the holes for you if you are local.

PMed you. Thanks!

 

[BA9092]

How do you guys feel about solely installing a front lip/diffuser if it's not too loud/extra? Since the Supra already has side skirts/rear aero pieces I feel like it wouldn't look out of place, as opposed to other cars where you would want to balance the remaining parts. Would it look odd at stock ride height?

The Maxton Design V2 and V3 front lips offer an add-on OEM-blending look. Both are quite subtle and blend in well with the existing pieces.

I've only seen replacement (carbon fiber) rear diffusers or add-on spats but not a huge selection compared to the front lips and splitters offered.

 

[SooopraSD]

She got some new shoes. Follow her IG: @sd.a90

 

[puzzled]

Pressured up the tires on my A90 in prep for my drive tomorrow (given it does not rain... driving in the rain = 2hours cleaning the car + 1 hour cleaning the tires + 1hour cleaning the garage.. no thanks).

 

[Bflood]

Finished up a couple add-ons..

 

[suicidaleggroll]

Installed the verus rear diff cooling plate, and swapped out my H&R springs for HKS hipermax adjustables

 

[SupraTimo]

Hi all, I have a question, do any of you know how to remove the rear lower bumper reflectors?
Not the ones on the sides, the ones above the exhaust tips!!
Thank you in advance

 

[suicidaleggroll]

Hi all, I have a question, do any of you know how to remove the rear lower bumper reflectors?
Not the ones on the sides, the ones above the exhaust tips!!
Thank you in advance

You can pull a few screws from the bottom of the rear diffuser and then you’ll have access to the back side of the reflectors. They’re held in with clips, I think 3 each. With access to the back you can use a screwdriver to pop the clip closest to the center of the car. From there you can grab that end of the reflector from behind the car and pry it out to pop the last two. It’s much easier than the other reflectors, only took me ~10 min to swap them out.

 

[zrk]

Hi all, I have a question, do any of you know how to remove the rear lower bumper reflectors?
Not the ones on the sides, the ones above the exhaust tips!!
Thank you in advance

You can actually just pop them out from the rear with a trim tool. Really easy. You don't need to undo any screws at all.

 

[starman]

Received my black slack valve stems (ordered from https://www.ebay.com/itm/143530237592?var=442486482012). Perfect OEM fitment: