Race Tracking Your Supra - Information exchange

[garudathree]

putting it on ppf is fine, just strip off any ceramic treatment

Sponsored

 

[kyle9]

Sweet. That was my initial thought, but now what I’m wondering about is the adhesive. This vent goes on with tape and adhesive promoter. I’m thinking it might be unwise to try to put that to the PPF instead of direct to the paint.

My Verus vent was taped onto my ppf'd hood. No issues

 

[theQuaybee]

Appreciate the feedback!

 

[FLtrackdays]

Another PB at Sebring. No new mods. 2:23s next target time - proper seats soon - mega sore bracing myself all weekend

Changed the pads out day 2. Had to scrub off too much speed on the front tires. Poor girl. It was my last track weekend for a while. Pushed the out of her



Not my fastest lap, but found a Vette that was a good driver. Went back & forth. Lots of fun!!

 

[Rensuhlo]

Didn't hit my goal time, but I still PBd by .5


Yes I know the sawblading needs to stop.


Bonus Shenanigans as seen from my BOSSBOSSVISION

 

[bushido]

Not my fastest lap, but found a Vette that was a good driver. Went back & forth. Lots of fun!!

Didn't hit my goal time, but I still PBd by .5


Yes I know the sawblading needs to stop.

nice

 

[Evolution]

Another PB at Sebring. No new mods. 2:23s next target time - proper seats soon - mega sore bracing myself all weekend

Changed the pads out day 2. Had to scrub off too much speed on the front tires. Poor girl. It was my last track weekend for a while. So I pushed the out of her



Not my fastest lap, but found a Vette that was a good driver. Went back & forth. Lots of fun!!

Do you leave it in auto shift mode? And in normal? Kind of what it sounds like as it shifts super early sometimes. Seems like you are leaving a lot of time on the table on the brake zones too.

 

[FLtrackdays]

Do you leave it in auto shift mode? And in normal? Kind of what it sounds like as it shifts super early sometimes. Seems like you are leaving a lot of time on the table on the brake zones too.

Both. That particular lap/session I was messing with the lane assist & and the nanny button. The little VCS (or TC brake light in the upper right corner) light was coming on briefly. It rarely happens but it did that session. I had to mess with it a few times.

I usually can set it before leaving the pits. Don’t know if I forgot or if it was just playing with me.

As far as the brakes, one of the ducts came off. Braking wasn’t as strong as usual. Hence my tires paid the price, scrubbing off more speed when missing the apex’s. Will have to get that fixed and try those magical CSG pads someday. That could make a big difference in times

Bonus Shenanigans as seen from my BOSSBOSSVISION

That’s freaking hilarious Loved the subtitles and the baby video I did good just overlaying the data and transferring it to the computer. I thought you were going to loose it for sure on that one over snap. If I slide too much, I usually throw up a thumbs up to the corner workers, saying all good or my bad. However they want to take it, lol.

 

[Oodis]

Another PB at Sebring. No new mods. 2:23s next target time - proper seats soon - mega sore bracing myself all weekend

Changed the pads out day 2. Had to scrub off too much speed on the front tires. Poor girl. It was my last track weekend for a while. Pushed the out of her



Not my fastest lap, but found a Vette that was a good driver. Went back & forth. Lots of fun!!

Love seeing blokes having fun and going hard

track looks like a good track for the supra

cheers

 

[theQuaybee]

Been doing lots of measuring! Ripped off first sketch and this one is much better. 18.5” from the tip of the hood is the bottom cut line based on the GT4, so I’m told. All measurements are checking out but I’m going to sleep on it and measure again before cutting. I feel a lot better about it than the first sketch

 

[i3igpete]

Just disconnect it every time you do an alignment. Alignments shouldn't take more than.... six hours then.

Sooo apparently Dinan also realized the jamnut location was no bueno, and solved it a different way

 

[razorlab]

Sooo apparently Dinan also realized the jamnut location was no bueno, and solved it a different way

Exactly how the Whiteline arms where designed on my Evo 10.

 

[theQuaybee]

Issa hole. Going to take a sander/grinder to the exposed edges to clean them up a bit, then planning to get the vent set on tomorrow night so that I can try and get some track time in on Saturday. It won't be hot hot out, but it'll be over 80*, and that's plenty hot to get some data on this thing.

 

[Ryan T]

Those on Hawk 60/30, what was your bed in process?

 

[kungfujedis]

Got out on track with my Supra for the first time. All stock except for pads and fluid. I'll have to come up with an alternative camera mount arrangement. The narrow windshield and display block the view when i lean into a turn. I didn't think of that, as it wasn't a problem in my WRX. It was a blast! I realized i need a louder exhaust so i can feel faster

Sponsored