Overheating on track - looking for solution for 2-port engine

[Golden_S]

Hey,
I have a problem with overheating on track. After 1 hard lap I hit over 280F on oil.
Current setup: 495hp, 750nm (custom map based on MHD), max cooling mode. Supporting mods: bigger water cooler, middle mounted engine oil cooler.
What I have heard is that 2-port engines tends to overheat but 6-port not. Unfortuantely I have the 2-port one.
One of tuners told me that methanol injection into charge pipe would solve the problem. I have also seen somebody put water spray into intercooler.
Do you have any proven solutions? I have already put a lot of money into coolers but it gave almost no result.

Sponsored

 

[Hasan]

I cannot understand how reducing the intake temps will have a significant impact on engine oil temps.

It seems your "Max cooling" mode is not working. Try to reflash the tune and make sure it is actually activated.

What sort of temps do you see in normal driving conditions?

Since, you already have bigger water coolers and an engine oil cooler as well, perhaps hood vents would make some difference.

Is it possible that your engine heat management module is not working properly?

 

[omfgzilla]

I mean 280 is high but not uncommon, and something I would expect to hit eventually after a long session.
If it's not a max cooling config issue, you could try another oil cooler. I'm not sure which kit you have, but the Verus setup uses a PWR heat exchanger. It replaces one of the auxiliary radiators and deletes the OEM water2oil heat exchanger, so you'll dump less heat into the coolant loop.
Supra Oil Cooler Data Overview | Verus Engineering - YouTube

like hasan mentioned hood vents will help overall. A catless downpipe would relieve some backpressure and less radiant heat in the engine bay. Don't bother buying an aftermarket heat exchanger.
IAT's are the usual........... Water/meth, intake manifold or a larger turbo running within its efficiency island. The jury's still out on Interchillers.

 

[Golden_S]

I cannot understand how reducing the intake temps will have a significant impact on engine oil temps.

It seems your "Max cooling" mode is not working. Try to reflash the tune and make sure it is actually activated.

What sort of temps do you see in normal driving conditions?

Since, you already have bigger water coolers and an engine oil cooler as well, perhaps hood vents would make some difference.

Is it possible that your engine heat management module is not working properly?

In normal conditions oil temp is around 200f. Even when pushig it on highwaygoing 100mph +.
I have hood vent ready to be mounted so maybe it will change something but I doubt in radical change

 

[Golden_S]

I mean 280 is high but not uncommon, and something I would expect to hit eventually after a long session.
If it's not a max cooling config issue, you could try another oil cooler. I'm not sure which kit you have, but the Verus setup uses a PWR heat exchanger. It replaces one of the auxiliary radiators and deletes the OEM water2oil heat exchanger, so you'll dump less heat into the coolant loop.
Supra Oil Cooler Data Overview | Verus Engineering - YouTube

like hasan mentioned hood vents will help overall. A catless downpipe would relief some backpressure and less radiant heat in the engine bay. Don't bother buying an aftermarket heat exchanger.
IAT's are the usual........... Water/meth, intake manifold or a larger turbo running within its efficiency island. The jury's still out on Interchillers.

I have catless downpipe. Oil cooler is custom work but it also elminates oem water2oil heat exchanger

 

[omfgzilla]

Oil cooler is custom work but it also elminates oem water2oil heat exchanger

Yea, forgot all oil cooler kits need the coolant2oil delete. When you say "middle mounted" I'm assuming you mean stacked Infront of the high temp heat exchanger, and not like this?

 

[Hasan]

It would be helpful to see how the oil cooler is mounted and what sort of shroud, if any, you have around it? Do you have an oil thermostat in there?

Does your oil cooler have an efficient exit path for the hot air?

Do you have a very aggressive anti-lag setup in your tune?

 

[Golden_S]

It would be helpful to see how the oil cooler is mounted and what sort of shroud, if any, you have around it? Do you have an oil thermostat in there?

Does your oil cooler have an efficient exit path for the hot air?

Do you have a very aggressive anti-lag setup in your tune?

Yea, forgot all oil cooler kits need the coolant2oil delete. When you say "middle mounted" I'm assuming you mean stacked Infront of the high temp heat exchanger, and not like this?

The radiator is mounted in front of the intercooler on the front belt. It measures 15x30 cm and takes up about half of the center air intake in the bumper. The kit looked like the one from Verus—a radiator, two hoses, and a heat exchanger. There are two water radiators in the wheel wells.

 

[razorlab]

When you say "bigger water cooler" are you referring to the big heat exchanger in the front cooling stack? If so, which one, engine or intake charge?

If not, are you talking about an upgraded intake manifold?

Let's get a clear baseline on the system here.

A datalog would also be helpful.

 

[Z4m40i]

280F is pretty typical for b58’s… I still can get up to 300F with the verus oil cooler.

running meth would help lower your IAT’s keeping your timing advanced which would help lower cylinder temps, so maybe that’s where your tuner is coming from. Ethanol would help cylinder temps as well, but I haven’t seen that help too much with oil temps.

what are your coolant and IAT temps? And what ambient temps are you tracking in?

 

[i3igpete]

Could you provide a source on where you heard 2 ports overheat more? I would like to discredit the source, rather than shoot the messenger.

For reference, stock power with hood vent and catless DP, at ACC-south (medium speed and technicality):

Sponsored